
We design the electronics of connected devices — from the first block diagram to boards that are ready for mass production. Our team of top experts, with an average of 15 years of experience in electronics design, supports you from initial concept through PCB design, manufacturing and certification.
At a glance
5 PCB designers with more than 15 years of experience: digital, power, RF, high-speed and HDI
Every stage: Discovery → PoC → EVT → DVT → PVT → Mass Production — join us at any of them
Simulation and reviews before every build, so problems show up on screen instead of in the lab
From discovery to mass production
Product stages
Discovery: requirements, block diagram, key component and platform choices, cost and time estimate
PoC (proof of concept): first prototype to show the idea works
EVT: first real boards — do the electronics work as designed?
DVT: near-final design in the enclosure, pre-compliance for EMC, thermal and environment
PVT: builds on the production line — yield, test fixtures, assembly
Mass production: DFM/DFA fixes, end-of-life components and alternates, design updates
Architecture and component selection
Block diagram, design specification and modes of operation
Platform choice backed by evaluation: we compared MediaTek, Rockchip and NXP SoMs for a smart fridge, and MPUs from seven vendors for an end-of-life redesign
Cost-aware choices: a microchip with a 16-bit ADC instead of a development board made a verification device smaller and cheaper
System documented with the C4 model in IcePanel
What we design
Platforms
SoMs, SBCs and SoCs
MCU, CPU, GPU, DSP and FPGA
Motor control: motors, stepper motors, PMSM and BLDC
Connectivity
Cellular 3G, 4G and 5G, satellite
Bluetooth LE (up to 5.x), Wi-Fi, Thread, LoRa/LoRaWAN, 6LoWPAN, Zigbee, RFID and NFC
GNSS: GPS, Galileo, GLONASS and BeiDou
Interfaces
PCIe Gen2/3/4, SATA R.3.x, LVDS, SDI
10/100/1000 Ethernet, USB up to 3.2, HDMI
MIPI-CSI and MIPI-DSI cameras and displays
Boards
PCB design and layout: multilayer (12+ layers), high-speed, HDI, flex and rigid-flex, RF
Stack-up and transmission-line design, DFM and DFA with IPC-compliant libraries
Schematic capture and component libraries
Simulation and reviews before every build
Simulation and analysis
We simulate to avoid costly re-spins, roll out faster and make hardware more reliable:
Signal integrity — pre- and post-layout
Power integrity — DC drop, decoupling, plane noise
Thermal simulation and 3D modeling for enclosure fit
Design reviews for your team
For companies with an in-house PCB team or another partner, we review the design against best practices:
Schematic review: interconnections and datasheets, electrical and signal-flow checks, compatibility between blocks, better component alternatives, BOM cost and end-of-life parts
PCB design review: stack-up, transmission lines, power and sensitive-signal routing, EMI/EMC and safety readiness, DFM and DFA
AI schematic integrity analysis as an extra check
Our design process
Block diagram and design specification
Component library
Schematic design and review
Component placement and layer-stack calculation
Pre-layout signal-integrity analysis
PCB routing and layout review
Post-layout SI, PI and thermal analysis
Design documentation
Testing and certification readiness
Testing, debugging and pre-certification (EMC, radio, safety) before a build goes to the lab
Certification requirements reviewed at the start and followed at every stage: FCC, CE, ISO, RoHS, UL
All documentation and test firmware for electronics certification and software audits
Support through CE and EMC lab testing, as for Glomex's marine 5G router
Next-generation connectivity
Bluetooth 6.0 Channel Sounding for distance measurement — see our field test on nRF54L15
Nordic nRF54 series, Wi-Fi 6 and Wi-Fi 7
5G RedCap modems, Matter over Thread, DECT NR+ and UWB
Electronics projects we've delivered
Glomex — marine 5G router
Hardware designed and certified, plus OpenWrt firmware for the first 5G router for the marine industry: dual SIM, carrier aggregation and internet up to about 20 miles offshore.
Rocco — smart beverage fridge
A complete system designed, integrated and validated: Linux main board after a SoM evaluation, a 3-camera computer-vision setup over MIPI, RS-232 control of the fridge electronics and Wi-Fi.
Stardust Secured — verification device
An optical verification device that works with a smartphone: LED emitters, photodetectors, preamps and a 16-bit ADC, one USB-C port for data, charging and uploads — from demo prototype to a production-ready tester.
Byte — smart kiosk fridge
Electronics redesigned into a modular architecture: new peripheral board, IIoT microcontroller, cellular modem SoM, sensor fusion and a tamper-evident lock.
FAQ
At what stage can you join a hardware project?
Any — Discovery, PoC, EVT, DVT, PVT or Mass Production. We also take over existing designs.
Do you only design the PCB, or the whole device?
Both. We can design the full electronics with firmware and enclosure, or only the board, the schematic or a review.
Can you redesign a board when a chip reaches end of life?
Yes. We evaluate replacement platforms, redesign the board and bring it up — for example a controller board moved from MIPS to an ARM STM32MP25.
Do you help with certification?
Yes. We design for FCC, CE, RoHS and UL requirements from the start, run pre-certification and support the lab testing. Certification itself is done by accredited labs.
Can you review our existing schematic or layout?
Yes — schematic and PCB layout reviews before you commit to a build.
Can you work inside our hardware team?
Yes. Our PCB designers can join your team and work in your tools and review cadence, as we did for an RF board at Nextivity.
Need help with a circuit board design?
Tell us what you're building and what stage it's at using the form below, and our hardware team will get back to you.




